• Skip to main content
  • Skip to secondary menu
  • Skip to primary sidebar
  • Home
  • Textile
    • Textile Calculation
    • Textile Flow Chart
    • Spinning
    • Yarn Manufacturing
      • Yarn Count
    • Textile Universities
    • Abbreviation
    • Template
  • Garments
    • Industrial Engineering (IE)
    • Standard Operating Procedure
    • Wet Processing
    • Dyeing
    • Fabric Dyeing and Printing
    • Fabric Cutting
    • Sewing
    • Garments Washing
    • Merchandising
      • Visual Merchandising
  • Fashion
  • Finance
    • Financial Calculation
    • Video Tutorial
    • Economics
    • Economy

ORDNUR

Textile and Finance

  • About
  • Contact
  • Privacy Policy
  • Terms and Conditions

Basic Operation in Blow Room

Blow Room: There are some methods of opening the mass of fibers into small tufts before further processing. This process of opening & clean is known as the blow room process. Blow room consists of a number of m/c degree 40% to 70% trash is removed in this section.

basic operation in blow room

Blow Room

Objects of Blow Room Process

  1. To open the compressed layer of a bale of cotton or any staple fibers with minimum damage to the fibers.
  2. To remove the impurities like sand, seed, bits, neps & short fibers present in the cotton with minimum loss of lint by opening & blending.
  3. To effect a thorough blending with minimum neps formation.
  4. To convert the mass of cotton fibers into a uniform thick sheet of cotton both longitudinally & transversely &fed as it in the case of chute feed system or wound in the form of a compactly built lap with minimum lap rejection.
  5. Intensive de-dusting of cotton fibers to extract micro-dust in order to improve the working of opened spinning m/c.
  6. Fiber recovery from the waste produced by the various processes the conversion of fiber to yarn in order to reduce the consumption of raw material.

Basic Operation in Blow Room

Opening

  • The opening is the first operation required carried out to the stage of flocks in the blow room & to the stage individual fibers in the card flock weight can be reduced to about 0.1mg in the room.

Cleaning

  • The blow room cannot eliminate all or even almost all of the foreign matter in the raw material.
  • A blow room installation removes approximately 40% to 70% of the impurities.
  • The result is dependent on raw material on the m/c s & on the environment.

Dust Removal

  • Dust removal is not easy operation since the dust particles are completely enclosed in the flocks & hence are back during suction.
  • The suction units remove dust 64 dust removal will more intensive the smaller the flocks.

Blending

  • Fibers can be blending at various stages of the process. These possibilities should always be exploited.
  • The start of the process is one of the most important stages of blending.
  • Intensive blending in a suitable blending m/c must be carried out after separate flock extraction from individual bales of the layout.
  • This blending operation must collect the sequentially arriving bunches of fibers from individual bales & mixes them thoroughly.

Even feed of material of the card

  • Finally, the blow room must ensure that raw material is evenly delivered to the cards. Previously, this was carried out by means of precisely weighed laps from the scutcher, but automatic flock feeding installations are increasingly being used.
  • While in the introductory phase such installations were subject to a problem regarding evenness of flock delivery, today they generally operate well or at least adequately.

Written by

Engineer Sheikh Nurja

B.Sc engineer of textile

Share this:

  • Click to share on Facebook (Opens in new window)
  • Click to share on LinkedIn (Opens in new window)
  • Click to share on WhatsApp (Opens in new window)
  • Click to email this to a friend (Opens in new window)

Related

Reader Interactions

Comments

  1. marimuthu chinnasami says

    May 3, 2015 at 8:24 pm

    post something in open end spinning

  2. Aditya says

    December 7, 2017 at 12:51 am

    This notes is really helpful to those who are searching ……..thank you plz rework to make this large and this type of notes should be provided to every student of Textile technology

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

Primary Sidebar

TOP ARTICLES

  • 27 Parts of a Sewing Machine With Details
  • Maximize the Value of a Corporation
  • Standard Minute Value: SMV in Garments, Calculation, Importance
  • Garments Quality SOP [updated]
  • Implementation of 5S in Apparel Industry

Categories

Subscribe Us

Join 5,383 other subscribers

Copyright © 2021 ORDNUR

Go to mobile version
loading Cancel
Post was not sent - check your email addresses!
Email check failed, please try again
Sorry, your blog cannot share posts by email.